KVNS? A2? ? Support Ring ? Metric
²úÎïÀàËÆÓÚ:
KVNS? A2? ? Support Ring ? Metric
Two support rings per cutter required.
ÎïÁϺÅ104202415
ÇëÁªÏµÎÒÃǵÄÏúÊÛÈËÔ±À´Á˽âÄúµÄ¶¨¼Û¡£
Features and benefits
- Cutter diameters 200mm and 250mm can be assembled with either the drive rings, or the supports ring.
- The support rings provide more stability, but depth of cut decreases with the support rings.
µ¶Æ¬Ñ¡ÔñÖ¸ÄÏ
| KVNS? A2? Slotting Cutters ? Insert Selection Guide | ||||||
| ²ÄÁÏ ·Ö×é | ÇáÇÐÏ÷ | ÖеÈÇÐÏ÷ | ÖØÇÐÏ÷ | |||
| ¨C | (·æÀûµÄ²ÛÐÍ) | (ǿ׳µÄ²ÛÐÍ) | ||||
| ¨C | ÄÍÄ¥ÐÔ |  | ÈÍÐÔ | |||
| ¨C | ²ÛÐÍ | ²ÄÖÊ | ²ÛÐÍ | ²ÄÖÊ | ²ÛÐÍ | ²ÄÖÊ |
| P1-P2 | .S..GD | KCPK30 | .S..GD | KCPK30 | .S..GB | KCPK30 |
| P3-P4 | .S..GD | KCPK30 | .S..GD | KCPK30 | .S..GB | KCPK30 |
| P5-P6 | .S..GD | KCPK30 | .S..GB | KCPK30 | .S..GB | KCPK30 |
| M1-M2 | .S..GD | KCPK30 | .S..GD | KCPK30 | .S..GB | KCPK30 |
| M3 | .S..GD | KCPK30 | .S..GB | KCPK30 | .S..GB | KCPK30 |
| K1-K2 | .S..GD | KCPK30 | .S..GD | KCPK30 | .S..GB | KCPK30 |
| K3 | .S..GD | KCPK30 | .S..GD | KCPK30 | .S..GB | KCPK30 |
| N1-N2 | ¨C | ¨C | ¨C | ¨C | ¨C | ¨C |
| N3 | ¨C | ¨C | ¨C | ¨C | ¨C | ¨C |
| S1-S2 | ¨C | ¨C | ¨C | ¨C | ¨C | ¨C |
| S3 | ¨C | ¨C | ¨C | ¨C | ¨C | ¨C |
| S4 | ¨C | ¨C | ¨C | ¨C | ¨C | ¨C |
| H1 | ¨C | ¨C | ¨C | ¨C | ¨C | ¨C |
ÍƼö³õʼ½ø¸øÂÊ [mm]
| KVNS? A2? Series ? Recommended Starting Feeds [mm/th] | |||||||||||||||
| µ¶Æ¬²ÛÐÍ | ²»Í¬Çпí(²¹±ð)°Ù·Ö±ÈÇé¿öÏ£¬Ëù½¨ÒéµÄÿ³Ý½ø¸øÁ¿É趨ֵ(´Ú³ú) | ||||||||||||||
| 5% | 10% | 20% | 30% | 40¨C100% | |||||||||||
| L | M | H | L | M | H | L | M | H | L | M | H | L | M | H | |
| .S..GD | 0,23 | 0,46 | 0,71 | 0,17 | 0,33 | 0,51 | 0,13 | 0,25 | 0,38 | 0,11 | 0,22 | 0,33 | 0,10 | 0,20 | 0,30 |
| .S..GB | 0,23 | 0,46 | 0,74 | 0,17 | 0,33 | 0,54 | 0,13 | 0,25 | 0,40 | 0,11 | 0,22 | 0,35 | 0,10 | 0,20 | 0,32 |
| L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use "Light Machining" values as starting feed rate. | |||||||||||||||
Recommended Starting Feeds [IPT]
| KVNS? A2? Series ? Recommended Starting Feeds [IPT] | |||||||||||||||
| µ¶Æ¬²ÛÐÍ | ²»Í¬Çпí(²¹±ð)°Ù·Ö±ÈÇé¿öÏ£¬Ëù½¨ÒéµÄÿ³Ý½ø¸øÁ¿É趨ֵ(´Ú³ú) | ||||||||||||||
| 5% | 10% | 20% | 30% | 40¨C100% | |||||||||||
| L | M | H | L | M | H | L | M | H | L | M | H | L | M | H | |
| .S..GD | 0.009 | 0.017 | 0.026 | 0.007 | 0.013 | 0.019 | 0.005 | 0.009 | 0.014 | 0.004 | 0.008 | 0.012 | 0.004 | 0.008 | 0.011 |
| .S..GB | 0.009 | 0.017 | 0.028 | 0.007 | 0.013 | 0.020 | 0.005 | 0.009 | 0.015 | 0.004 | 0.008 | 0.013 | 0.004 | 0.008 | 0.012 |
| L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use "Light Machining" values as starting feed rate. | |||||||||||||||
ÍƼö³õʼËÙ¶È [m/min]
| KVNS? A2? Series ? Recommended Starting Speed [m/min] | |||||||
| µ¶Æ¬²ÄÖÊ | KCPK30 | KMF | |||||
| ÇÐÏ÷ºñ¶È hex mm | ×îСֵ | ×î´óÖµ | ×îСֵ | ×î´óÖµ | |||
| ²ÄÁÏ ·Ö×é | ×î´óÖµ | ³õʼֵ | ×îСֵ | ×î´óÖµ | ³õʼֵ | ×îСֵ | |
| P | 1 | 455 | 395 | 370 | ¨C | ¨C | ¨C |
| 2 | 280 | 255 | 230 | ¨C | ¨C | ¨C | |
| 3 | 255 | 230 | 205 | ¨C | ¨C | ¨C | |
| 4 | 225 | 185 | 160 | ¨C | ¨C | ¨C | |
| 5 | 190 | 170 | 150 | ¨C | ¨C | ¨C | |
| 6 | 160 | 135 | 110 | ¨C | ¨C | ¨C | |
| M | 1 | 205 | 185 | 155 | ¨C | ¨C | ¨C |
| 2 | 185 | 160 | 140 | ¨C | ¨C | ¨C | |
| 3 | 145 | 130 | 115 | ¨C | ¨C | ¨C | |
| K | 1 | 295 | 265 | 240 | ¨C | ¨C | ¨C |
| 2 | 235 | 210 | 190 | ¨C | ¨C | ¨C | |
| 3 | 195 | 175 | 160 | ¨C | ¨C | ¨C | |
| N | 1 | ¨C | ¨C | ¨C | 335 | 298 | 271 |
| 2 | ¨C | ¨C | ¨C | 335 | 298 | 271 | |
| 3 | ¨C | ¨C | ¨C | 219 | 198 | 170 | |
| S | 1 | ¨C | ¨C | ¨C | 30 | 24 | 20 |
| 2 | ¨C | ¨C | ¨C | 30 | 24 | 20 | |
| 3 | ¨C | ¨C | ¨C | 30 | 24 | 20 | |
| 4 | 50 | 45 | 35 | 24 | 24 | 24 | |
| H | 1 | ¨C | ¨C | ¨C | ¨C | ¨C | ¨C |
| Recommended Starting Speed are pointing to 90¡ã Shoulder Milling . Starting Speed for Face and Copy Milling can be Increased by 20 %. As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining. | |||||||
Recommended Starting Speeds [SFM]
| KVNS? A2? Series ? Recommended Starting Speed [SFM] | |||||||
| µ¶Æ¬²ÄÖÊ | KCPK30 | KMF | |||||
| Chip Thickness hex Inch | ×îСֵ | ×î´óÖµ | ×îСֵ | ×î´óÖµ | |||
| ²ÄÁÏ ·Ö×é | ×î´óÖµ | ³õʼֵ | ×îСֵ | ×î´óÖµ | ³õʼֵ | ×îСֵ | |
| P | 1 | 1495 | 1295 | 1215 | ¨C | ¨C | ¨C |
| 2 | 920 | 835 | 755 | ¨C | ¨C | ¨C | |
| 3 | 835 | 755 | 675 | ¨C | ¨C | ¨C | |
| 4 | 740 | 605 | 525 | ¨C | ¨C | ¨C | |
| 5 | 625 | 560 | 490 | ¨C | ¨C | ¨C | |
| 6 | 525 | 445 | 360 | ¨C | ¨C | ¨C | |
| M | 1 | 675 | 605 | 510 | ¨C | ¨C | ¨C |
| 2 | 605 | 525 | 460 | ¨C | ¨C | ¨C | |
| 3 | 475 | 425 | 375 | ¨C | ¨C | ¨C | |
| K | 1 | 970 | 870 | 785 | ¨C | ¨C | ¨C |
| 2 | 770 | 690 | 625 | ¨C | ¨C | ¨C | |
| 3 | 640 | 575 | 525 | ¨C | ¨C | ¨C | |
| N | 1 | ¨C | ¨C | ¨C | 1100 | 980 | 890 |
| 2 | ¨C | ¨C | ¨C | 1100 | 980 | 890 | |
| 3 | ¨C | ¨C | ¨C | 720 | 650 | 560 | |
| S | 1 | ¨C | ¨C | ¨C | 100 | 80 | 65 |
| 2 | ¨C | ¨C | ¨C | 100 | 80 | 65 | |
| 3 | ¨C | ¨C | ¨C | 100 | 80 | 65 | |
| 4 | 165 | 150 | 115 | 80 | 80 | 80 | |
| H | 1 | ¨C | ¨C | ¨C | ¨C | ¨C | ¨C |
| Recommended Starting Speed are pointing to 90¡ã Shoulder Milling . Starting Speed for Face and Copy Milling can be Increased by 20 %. As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining. | |||||||